Features
DEUTZ 3.6L TIER 4F (STAGE IV) ENGINE
The Deutz 3.6L Tier 4F (Stage IV) engine meets all U.S., Canada and European Union tier/stage regulations.
DRUM SERVICE ACCESS
A single large drum door along the side and entry from the end provide superior drum service access.
LOW HOPPER HEIGHT
A low hopper infeed height helps to decrease loading cycle times and eliminates the need for loading ramps with most loaders.
QUICK CHANGE DRUM
Efficiently change product size by exchanging drums
QUICK CHANGE SCREENS
Screen changes can help improve jobsite efficiency, a particularly important feature when processing a range of materials that requires frequent screen changes. The design also creates a smooth exterior on the drum, reducing the amount of brush wear.
SQUARE LIFT BARS
Square lift bars inside the drum enable more material to be carried at a slower drum speed helping decrease fuel consumption and premature wear.
SWING-OUT ENGINE BAY
A single large access door provides engine service access.
TENSIONED SCREENS
Compatibility with smaller gauge wire increases the open screen area thus overall production of the machine, particularly in applications when processing wetter materials.
VERMEER ACS CONTROL SYSTEM
These control systems offer the operator flexibility when operating from the machine or cab of the loader. Operators can also adjust conveyor height from the remote, providing the ability to keep them low to the ground to reduce blowing of material.
Specs
| GENERAL DIMENSIONS AND WEIGHTS | |
| Weight | 37000 lbs |
| Hitch Weight | 4200 lbs |
| Transport Length | 40 ft |
| Transport Width | 99 in |
| Transport Height | 13.1 ft |
| Operation Length | 54 ft |
| Operation Width | 295 in |
| Operation Height | 16.7 ft |
| Capacity | Approximately 180 cu yd (137.6 cu m) per hour with 0.5 in (1.3 cm) screens installed and material with moisture less than 40% |
| ENGINE - OPTION ONE | |
| Make and Model | Deutz 3.6L Tier 4F (Stage IV) |
| Number of Cylinders | 4 |
| Engine Rating | 100 hp (74.5 kW) |
| Fuel Tank Capacity | 50 gal |
| Fuel Consumption | 3 gph (11.4 L/h) |
| Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles) | 30 deg |
| Battery | 950 CCA |
| Oil Filter | Spin-on |
| Recommended Oil | Mobil 15W40 |
| Oil Volume with Filter | 10 qt |
| System Voltage | 12 V, 120 amp alternator |
| Air Cleaner | Dual element |
| Radiator Fan | Suction |
| HYDRAULIC SYSTEM | |
| Operation | 77.8 gpm @ 3000 psi (294.5 L/min @ 206.8 bar) |
| Tank capacity | 80 gal |
| CHASSIS | |
| Frame Description | Four independent hydraulic jacklegs |
| Axle/Suspension | Leaf spring |
| Tires - Option One | 445/50 R22.5 |
| HOPPER AND APRON CONVEYOR | |
| Hopper Capacity | 6.5 cu yd |
| Hopper Bottom Width | 37.5 in |
| Apron Conveyor Speed | 0-15 fpm |
| Apron Opening Height | 45 in |
| Apron Opening Width | 37.5 in |
| Hopper Height | 9.5 ft (2.9 m) from ground level at operating incline |
| Hopper Opening | 11.7 ft x 5.3 ft (3.57 m x 1.6 m) |
| Apron Conveyor Length | 12.4 ft |
| Apron Conveyor Belt Width | 42 in |
| Apron Conveyor Rollers | 5 CEMA "D" x 17 in (12.7 x 43.2 cm) |
| SCREEN DRUM | |
| Drum Operation | 0-33.1 gpm (0-125.3 L/min) |
| Drum Motor | 35.5 cu in (581.7 cu cm) displacement |
| Drum Diameter | 6.5 ft |
| Drum Support Description | 8 polyurethane trunnion wheels on pivoting bogeys 8 od x 4 in wide (20.3 x 10.2 cm) |
| Drum Length | 20 ft |
| Thrust Bearing Diameter | 4 in |
| Thrust Bearing Face | 2 in |
| Drum Speed | 0-25 rpm |
| Drum Drive Chain | 140 extended pin/extended width |
| Drum Angle Adjustability | 0-5 deg |
| Maximum Screen Panels | 8 |
| SCREEN BRUSHES | |
| Brush Diameter | 14 in |
| Bristle Material | Polyethylene |
| Brush Assembly Support | Two 1.25 in (3.2 cm) sealed ball bearings/brush |
| COLLECTING CONVEYOR | |
| Collecting Conveyor Length | 16 ft |
| Collecting Belt Speed | 360 ft/min |
| Conveyor Belt Width | 36 in |
| Conveyor Belt Type | 220 lb (99.8 kg), 2 ply, 2/6" x 1/16" (4.8 mm x 1.6 mm) |
| Head/Tail Pulley Type | 8 in (20.3 cm) crowned |
| Head Pulley Bearing | 1.75 in (4.4 cm) double roller |
| Rubber Flashing | Adjustable corded rubber |
| Idler Type | 4 in (10.2 cm) CEMA "B" straight |
| Tail Pulley Takeup | 6 in |
| Self-Cleaning Return Idlers | 4 in (10.2 cm) rubber disk x 3 |
| Fines Conveyor Frame | Part of trailer frame |
| FINES CONVEYOR | |
| Conveyor Motor Displacement | 14.2 cu-in |
| Fines Conveyor Length | 23.5 ft |
| Fines Belt Speed | 400 ft/min |
| Conveyor Belt Width | 36 in |
| Conveyor Belt Type | 220 lb (99.8 kg), 2 ply, 2/16 x 1/16 in (4.8 mm x 1.6 mm) smooth |
| Conveyor Belt Stacking Height | 10.5 ft (3.2 m) (conveyor @ 30 deg) |
| Head Pulley Type | 8 in (20.3 cm) crowned |
| Head Pulley Bearing | 1.5 in (3.8 cm) pillow block |
| Troughing Idler Type | 20 deg CEMA "B" with permanently sealed bearings spaced at 40-in centers |
| Self-Cleaning Tail Pulley Dimensions | 8 in diameter, 38 in wide, crowned wing pully |
| Head Pulley Takeup | 8 in |
| Self-Cleaning Return Idlers | 2, 4 in (10.2 cm) diameter; 1, 5 in (12.7 cm) diameter, "rattle roller" |
| Fines Conveyor Frame | Engineered structural frame |
| OVERS CONVEYOR - OPTION 1 | |
| Overs Conveyor Length | 19.2 ft |
| Maximum Variable Overs Belt Speed | 360 ft/min |
| Conveyor Belt Size | 42 in (106.7 cm) |
| Conveyor Belt Type | 220 lb (99.8 kg), 2 ply, 2/16 x 1/16 in (4.8 x 1.6 mm) cleated |
| Conveyor Belt Stacking Height | 9 ft (2.7 m) (conveyor @ 25 deg) |
| Head Pulley Type | 8 in (20.3 cm) crowned |
| Head Pulley Bearing | 1.5 in (3.8 cm) pillow block |
| Self-Cleaning Tail Pulley Dimensions | 8 in (20.3 cm) diameter, 44 in (111.8 cm) wide, crowned wing pulley, 1.75 in (4.4 cm) shaft |
| Head Pulley Takeup | 8 in |
| Self-Cleaning Return Idlers | 2, 4 in (10.2 cm) diameter; 1, 5 in (12.7 cm) diameter, "rattle roller" |
| Overs Conveyor Frame | Engineered structural frame |
| Troughing Idler Type | 20 degrees CEMA "B" with permanently sealed bearings spaced at 32-in centers |
Copyright © 2026 - All Rights Reserved - EquipmentLocator.com