Features
HIGH PRODUCTION
The tensioned screens around the drum add rigidity, allowing use of small gauge wire, which helps increase production capacity and enable processing of wetter material.
MOTOR STARTER PANEL
The motor starter panel provides a variable frequency drive (VFD) panel.
ELECTRIC MOTORS
Powered by two industrial-duty, fully enclosed and fan-cooled electric motors. A single 150-hp (112-kW) motor powers the hydraulic pump stack while a .75-hp (.6-kW) motor powers the cooling fan for the hydraulic system.
EASE OF MAINTENANCE
The TR626EM was built with the operator in mind, designed with various access points to critical areas helping to make maintenance efficient.
ADVANCE CONTROLS
Operators can control the machine through either the Vermeer DP10 display mounted on the control panel, or through a handheld transceiver remote.
RADIAL STACKING CONVEYOR
The stacking conveyor with a 180-degree arc increases the amount of material being stacked on the ground. Adjustable stacking height aids with dust control and helps avoid material being blown away.
Specs
| GENERAL DIMENSIONS AND WEIGHTS | |
| Weight | 65000 lbs |
| Hitch Weight | 30000 lbs |
| Transport Length | 54.5 ft |
| Transport Width | 113 in |
| Transport Height | 13.5 ft |
| Operation Length | 84.4 ft |
| Operation Width | 113 in |
| Operation Height | 15.9 ft |
| Capacity | Approximately 200 cu yd (152.9 cu m) per hour with 0.5 in (1.3 cm) screens installed and material with moisture less than 40% |
| MOTOR OPTION ONE | |
| Make and Model | Siemens |
| Motor rating | 150 hp, 1800 rpm, 460 V, 3 phase |
| System Voltage | 12 V, 120 amp alternator |
| HYDRAULIC SYSTEM | |
| Operation | 62.9 gmp @ 2800 psi (238.1 L/min @ 172.4 bar [17240 kPa]) |
| Tank capacity | 200 gal |
| CHASSIS | |
| Frame Description | 4 independent hydraulic jacklegs |
| Axle/Suspension | Leaf spring |
| Capacity | 22500 lbs |
| Tires - Option One | 235-75R 17.5H qty. 4 |
| HOPPER AND APRON CONVEYOR | |
| Hopper Capacity | 6 cu yd |
| Hopper Bottom Width | 48 in |
| Apron Conveyor Speed | 0-205 fpm (0-62.5 m/min) |
| Apron Opening Height | 34 in |
| Apron Opening Width | 43 in |
| Hopper Height | 9.5 ft (2.9 m) from ground level at operating incline |
| Hopper Opening | 13.2 ft x 5.3 ft (4 m x 1.6 m) |
| Apron Conveyor Length | 16 ft |
| Apron Conveyor Belt Width | 48 in |
| Apron Conveyor Rollers | 4 in (10.2 cm) diameter qty. 14 |
| SCREEN DRUM | |
| Drum Operation | 0-42.6 gpm (161.3 L/min) |
| Drum Motor | 48.8 cu in (800 cu cm) displacement |
| Drum Diameter | 6 ft |
| Drum Support Description | Four steel trunnion rollers 8 in (20.3 cm) diameter, 4 in (10.2 cm) width |
| Drum Length | 26 ft |
| Thrust Bearing Diameter | 5 in |
| Thrust Bearing Face | 2.9 in |
| Drum Speed | 0-21.6 rpm |
| Drum Drive Chain | 140 WT |
| Drum Angle Adjustability | 3-5 deg |
| Maximum Screen Panels | 8 |
| SCREEN BRUSHES | |
| Brush Diameter | 14 in |
| Bristle Material | Polyethylene |
| Brush Assembly Support | Two 1.25-in (3.2-cm) sealed ball bearings |
| COLLECTING CONVEYOR | |
| Conveyor Motor Displacement | 32.7 cu-in |
| Fines Belt Speed | 405 ft/min |
| Conveyor Belt Width | 36 in |
| Conveyor Belt Type220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm) | 220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm) |
| Head/Tail Pulley Type | Rubber-lagged, 12 in (30.5 cm ) diameter, 38 in (99.65 cm) wide |
| Head Pulley Bearing | 2.4 in (6.1 cm) pillow block |
| Rubber Flashing | Adjustable, 0.25 in (6.44 cm) thick, 4 in (10.2 cm) |
| Idler Type | 20 degrees CEMA "B" with permanently sealed bearings spaced at 24 in (20.96 cm) centers |
| Tail Pulley Takeup | 12 in |
| Self-Cleaning Return Idlers | 6, each 4 in (10.2 cm) diameter |
| Fines Conveyor Frame | Part of trailer frame |
| FINES CONVEYOR | |
| Conveyor Operation | 15.4 gpm |
| Conveyor Motor Displacement | 32.7 cu-in |
| Fines Conveyor Length | 72.5 ft |
| Fines Belt Speed | 405 ft/min |
| Conveyor Belt Width | 36 in |
| Conveyor Belt Type | 220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm) |
| Conveyor Belt Stacking Height | 16.6 ft (5.1 m) with drum at 4 deg |
| Head Pulley Type | Rubber lagged, 12 in (30.5 cm) diameter, 38 in (99.65 cm) wide |
| Head Pulley Bearing | 2.4 in (6.1 cm) pillow block |
| Rubber Flashing | Adjustable, 0.25 in (0.64 cm) thick, 4 in (10.16 cm) |
| Troughing Idler Type | 20 degrees CEMA "B" with permanently sealed bearings spaced at 24 in (60.96 cm) centers |
| Self-Cleaning Tail Pulley Dimensions | 10 in (25.4 cm) diameter, 38 in (96.5 cm) wide with 2.4 in (6.1 cm) shaft |
| Tail Pulley Takeup | 12 in |
| Self-Cleaning Return Idlers | 11, each 4 in (10.2 cm) diameter |
| Fines Conveyor Frame | 4 in x 8 in (10.2 cm x 20.3 cm) structural steel tubing |
| FINES CONVEYOR OPTION-RADIAL | |
| Conveyor Motor Displacement | 15.9 cu-in |
| Fines Conveyor Length | 30.5 ft |
| Fines Belt Speed | 705 ft/min |
| Conveyor Belt Type | 150 lb (99.8 kg), 2-ply, 1/32 in x 1/32 in (0.8 mm x 0.8 mm), vulcanized |
| Head/Tail Pulley Type | Rubber lagged, crowned, 9.75 in (24.8 cm) diameter, 32 in (81.3 cm) wide |
| Head Pulley Bearing | 1.94 in (4.9 cm) pillow block |
| Rubber Flashing | Adjustable, 0.25 in (6.4 mm) thick, 4 in (10.2 cm) |
| Idler Type | 30 degrees CEMA "B" with permanently sealed bearings spaced at 41 in (104 cm) centers |
| Self-Cleaning Return Idlers | 4, each 4 in (10.2 cm) diameter |
| Fines Conveyor Frame | 2 in x 8 in (5.1 cm x 20.3 cm) structural steel building |
| OVERS CONVEYOR - OPTION 1 | |
| Overs Conveyor Length | 20 ft |
| Maximum Variable Overs Belt Speed | 290 ft/min |
| Conveyor Belt Size | 48 in (121.9 cm) wide with raised cleat |
| Conveyor Belt Type | 220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm) |
| Conveyor Belt Stacking Height | 3 ft (0.9 m) x 10 ft (3.1 m) |
| Head Pulley Type | Rubber lagged, 12 in (30.5 cm) diameter, 51 in (99.65 cm) wide |
| Head Pulley Bearing | 2.4 in (6.1 cm) pillow block |
| Self-Cleaning Tail Pulley Dimensions | 10 in (25.4 cm) diameter, 51 in (129.5 cm) wide with 2.4 in (6.1 cm) shaft |
| Tail Pulley Takeup | 12 in |
| Solid Return Idler Size | 4-in diameter |
| Overs Conveyor Frame | 4 in x 8 in (10.2 cm x 20.3 cm) structural steel tubing |
| OVERS CONVEYOR - OPTION 2 | |
| Overs Conveyor Length | 28 ft |
| Maximum Variable Overs Belt Speed | 290 ft/min |
| Conveyor Belt Size | 48 in (121.9 cm) wide with raised cleat |
| Conveyor Belt Type | 220 lb (99.8 kg), 2-ply, 2/16 in x 1/16 in (4.8 mm x 1.6 mm) |
| Conveyor Belt Stacking Height | 3 ft (0.9 m) x 12.5 ft (3.8 m) |
| Head Pulley Type | Rubber lagged, 12 in (30.5 cm) diameter, 51 in (99.65 cm) wide |
| Head Pulley Bearing | 2.4 in (6.1 cm) pillow block |
| Self-Cleaning Tail Pulley Dimensions | 10 in (25.4 cm) diameter, 51 in (129.5 cm) wide with 2.4 in (6.1 cm) shaft |
| Head Pulley Takeup | 10 in |
| Rubber disc return idler size | 4 in diameter |
| Rattler roller return idler size | 5.4 in diameter |
| Overs Conveyor Frame | 2 in x 8 in (5.1 cm x 20.3 cm) structural steel tubing |
Copyright © 2026 - All Rights Reserved - EquipmentLocator.com