Features
STARTUP DELAY AND ALARM SYSTEMS
Enhance worker safety with startup delay and alarm systems that notify your whole crew when the machine is about to start.
TALL, WIDE THROAT OPENING
Move material smoothly without bridging, thanks to a tall, wide throat opening.
HEAVY-DUTY ROLLERS
Extend belt life even under tough loading conditions with closely set, heavy-duty rollers supporting the apron conveyor.
KEEP SCREEN WEIGHTS LOW
Keep screen weights low when processing wet materials by clamping on a smaller diameter tension screen wire and increasing screening area.
REDUCED SPILLAGE
Speed up your clean up because the flashing and sheeting fit tightly against the drum and conveyors to reduce spillage.
LOW HOPPER INFEED HEIGHT
Forget the loading ramps, since the 626 has a low hopper infeed height.
Specs
| GENERAL DIMENSIONS AND WEIGHTS | |
| Weight | 65000 lbs |
| Hitch Weight | 30000 lbs |
| Transport Length | 54.5 ft |
| Transport Width | 113 in |
| Transport Height | 13.5 ft |
| Operation Length | 84.4 ft |
| Operation Width | 113 in |
| Operation Height | 15.9 ft |
| Capacity | Approximately 200 cu yd (152.9 cu m) per hour with .5" (1.3 cm) screens installed and material with moisture less than 40% |
| ENGINE - OPTION ONE | |
| Make and Model | John Deere PowerTech PVX 4.5L, 4045HFC93 Tier 4F |
| Number of Cylinders | 4 |
| Engine Rating | 134 hp (93.2 kW) @ 2400 rpm, 398 ft-lb (531.6 Nm) of torque @ 1600 rpm |
| Fuel Tank Capacity | 73 gal |
| Fuel Consumption | 3.5 gph (13.3 L/hr) under most operating conditions |
| Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles) | 30 deg |
| Battery | 950 cold cranking amps |
| Oil Filter | Spin-on |
| Recommended Oil | Mobil 15/40 |
| Oil Volume with Filter | 15.5 qt |
| System Voltage | 12 V, 120 amp alternator |
| Air Cleaner | Dual element oversized |
| Radiator Fan | Suction-type |
| ENGINE - OPTION TWO | |
| Make and Model | John Deere 4045H Tier 3 |
| Number of Cylinders | 4 |
| Engine Rating | 125 hp (93.2 kW) @ 2400 rpm, 355 ft-lb (481.3 Nm) of torque @ 1500 rpm |
| Fuel Tank Capacity | 100 gal |
| Fuel Consumption | 3.5 gph (13.3 L/hr) under most operating conditions |
| Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles) | 30 deg |
| Battery | 950 cold cranking amps |
| Oil Filter | Spin-on |
| Oil Volume with Filter | 15.5 qt |
| System Voltage | 12 V, 120 amp alternator |
| Air Cleaner | Dual element oversized |
| Radiator Fan | Pusher type |
| HYDRAULIC SYSTEM | |
| Operation | 62.9 gpm @ 2800 psi (238.1 L/min @ 172.4 bar [17240 kPa]) |
| Tank capacity | 200 gal |
| CHASSIS | |
| Frame Description | 4 independent hydraulic jacklegs |
| Axle/Suspension | Leaf spring |
| Capacity | 22500 lbs |
| Tires - Option One | 235-75R 17.5H qty. 4 |
| HOPPER AND APRON CONVEYOR | |
| Hopper Capacity | 6 cu yd |
| Hopper Bottom Width | 48 in |
| Apron Conveyor Speed | 0-205 fpm (0-62.5 m/min) |
| Apron Opening Height | 34 in |
| Apron Opening Width | 43 in |
| Hopper Height | 9.5' (2.9 m) from ground level at operating incline |
| Hopper Opening | 13.2' x 5.3' (4 m x 1.6 m) |
| Apron Conveyor Length | 16 ft |
| Apron Conveyor Belt Width | 48 in |
| Apron Conveyor Rollers | 4" (10.2 cm) diameter qty. 14 |
| SCREEN DRUM | |
| Drum Operation | 0-42.6 gpm (161.3 L/min) |
| Drum Motor | 48.8 cu in (800 cu cm) displacement |
| Drum Diameter | 6 ft |
| Drum Support Description | Four steel trunnion rollers 8 in (20.3 cm) diameter 4 in (10.2 cm) width |
| Drum Length | 26 ft |
| Thrust Bearing Diameter | 5 in |
| Thrust Bearing Face | 2.9 in |
| Drum Speed | 0-21.6 rpm |
| Drum Drive Chain | 140 WT |
| Drum Angle Adjustability | 3-5 degrees |
| Maximum Screen Panels | 8 |
| SCREEN BRUSHES | |
| Brush Diameter | 14 in |
| Bristle Material | Polyethylene |
| Brush Assembly Support | Two 1.25" (3.2 cm) sealed ball bearings |
| COLLECTING CONVEYOR | |
| Conveyor Motor Displacement | 32.7 cu-in |
| Fines Belt Speed | 405 ft/min |
| Conveyor Belt Width | 36 in |
| Conveyor Belt Type | 220 lb (99.8 kg), 2-ply, 2/16" x 1/16" (4.8 mm x 1.6 mm) |
| Head/Tail Pulley Type | Rubber-lagged, 12" (30.5 cm) diameter, 38" (996.5 cm) wide |
| Head Pulley Bearing | 2.5" (6.4 cm) pillow block |
| Rubber Flashing | Adjustable, .25" (6.44 cm) thick, 4" (10.2 cm) |
| Idler Type | 20 degrees CEMA "B" with permanently sealed bearings spaced at 24" (60.96 cm) centers |
| Tail Pulley Takeup | 12 in |
| Self-Cleaning Return Idlers | 6, each 4" (10.2 cm) diameter |
| Fines Conveyor Frame | Part of trailer frame |
| FINES CONVEYOR | |
| Conveyor Operation | 15.4 gpm |
| Conveyor Motor Displacement | 32.7 cu-in |
| Fines Conveyor Length | 72.5 ft |
| Fines Belt Speed | 405 ft/min |
| Conveyor Belt Width | 36 in |
| Conveyor Belt Type | 220 lb (99.8 kg), 2 ply, 2/16" x 1/16" (4.8 mm x 1.6 mm) |
| Conveyor Belt Stacking Height | 16.6' (5.1 m) with drum at 4 degrees |
| Head Pulley Type | Rubber lagged, 12" (30.5 cm) diameter, 38" (996.5 cm) wide |
| Head Pulley Bearing | 2.5" (6.4 cm) pillow block |
| Rubber Flashing | Adjustable, .25" (.64 cm) thick, 4" (10.16 cm) |
| Troughing Idler Type | 20 degrees CEMA "B" with permanently sealed bearings spaced at 24" (60.96 cm) centers |
| Self-Cleaning Tail Pulley Dimensions | 10" (25.4 cm) diameter, 38" (96.5 cm) wide with 2.4" (6.1 cm) shaft |
| Tail Pulley Takeup | 12 in |
| Self-Cleaning Return Idlers | 11, each 4" (10.2 cm) diameter |
| Fines Conveyor Frame | 4" x 8" (10.2 cm x 20.3 cm) structural steel tubing |
| FINES CONVEYOR OPTION-RADIAL | |
| Conveyor Motor Displacement | 15.9 cu-in |
| Fines Conveyor Length | 30.5 ft |
| Fines Belt Speed | 705 ft/min |
| Conveyor Belt Type | 150 lb (99.8 kg), 2 ply, 1/32" x 1/32" (.8 mm x 0.8 mm), vulcanized |
| Head/Tail Pulley Type | Rubber lagged, crowned, 9.75" (24.8 cm) diameter, 32" (81.3 cm) wide |
| Head Pulley Bearing | 2.5" (6.4 cm) pillow block |
| Rubber Flashing | Adjustable, .25" (6.4 mm) thick, 4" (10.2 cm) |
| Idler Type | 30 degrees CEMA "B" with permanently sealed bearings spaced at 41" (104 cm) centers |
| Self-Cleaning Return Idlers | 4, each 4" (10.2 cm) diameter |
| Fines Conveyor Frame | 2" x 8" (5.1 cm x 20.3 cm) structural steel building |
| OVERS CONVEYOR - OPTION 1 | |
| Overs Conveyor Length | 19 ft |
| Maximum Variable Overs Belt Speed | 290 ft/min |
| Conveyor Belt Size | 48" (121.9 cm) wide with raised crescent |
| Conveyor Belt Type | 220 lb (99.8 kg), 2 ply, 2/16" x 1/16" (4.8 mm x 1.6 mm) |
| Conveyor Belt Stacking Height | 3' (.9 m) x 10' (3.1 m) |
| Head Pulley Type | Rubber lagged, 12" (30.5 cm) diameter, 38" (996.5 cm) wide |
| Head Pulley Bearing | 2.5" (6.4 cm) pillow block |
| Self-Cleaning Tail Pulley Dimensions | 10" (25.4 cm) diameter, 51" (129.5 cm) wide with 2.4" (6.1 cm) shaft |
| Tail Pulley Takeup | 12 in |
| Solid Return Idler Size | 4" x 8" diameter |
| Overs Conveyor Frame | 4" x 8" (10.2 cm x 20.3 cm) structural steel tubing |
Copyright © 2026 - All Rights Reserved - EquipmentLocator.com