Features
STANDARD FOUR-WHEEL DRIVE
The SC382 stump cutter is equipped with standard four-wheel drive to offer traction and maneuverability in difficult transport conditions.
OPERATOR PRESENCE SYSTEM
The operator presence system is intended to enhance operator safety by automatically stopping the cutter wheel when the operator releases the hydraulic cutter wheel controls.
OPTIONAL HYDRAULIC FRONT BLADE
The optional hydraulic front blade helps to reduce the amount of manual work during jobsite clean-up.
37 HP (26.1 KW) EFI BRIGGS AND STRATTON VANGUARD ENGINE
The SC382 stump cutter has a 37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine.
Specs
| GENERAL DIMENSIONS AND WEIGHTS | |
| Length | 118 in |
| Width | 50.1 in |
| Height | 53 in |
| Overall Width Transport (without duals) | 35.5 in |
| Weight - Engine Option One | 1950 lbs |
| Weight With Chip Blade Option (Additional) | 85 lbs |
| ENGINE - OPTION ONE | |
| Make and Model | Briggs & Stratton Vanguard EFI |
| Number of Cylinders | 2 |
| Gross Horsepower (Maximum) | 37 hp |
| Torque (Max) | 49 ft-lb |
| Fuel Tank Capacity | 10 gal |
| Max Fuel Consumption | 3.2 gph |
| Fuel Type | Gas |
| Air Cleaner | Dry-type safety element and restriction indicator |
| Oil Filter | Spin-on |
| Recommended Oil | 10W30 (See engine manual) |
| Oil Volume with Filter | 2.5 qt |
| Maximum Angle of Continuous Operation | 25 deg |
| Cooling Medium | Air |
| Alternator | 20/50 amp (rpm-based) |
| Clutch Type | Electric clutch with brake |
| CUTTERWHEEL SYSTEM | |
| Cutterwheel Diameter without Teeth | 17 in |
| Cutterwheel Thickness | .5 in |
| Cutterwheel Speed | 1560 epm |
| Cutterwheel Straight Line Dimension | 47 in |
| Cutterwheel Cut Above Ground | 24 in |
| Cutterwheel Cut Below Ground | 15 in |
| Tooth Description | Yellow Jacket cutter system |
| Number of Teeth | 20 |
| Number of Indexes | 2 |
| Number of Pockets | 20 |
| Reversible Pockets | 20 |
| Cutterwheel Guard | Standard |
| Chip Containment | 7.5 cu ft |
| CUTTERWHEEL DRIVE COMPONENTS | |
| Belt Type | V-Belt |
| Number of Primary Belts | 2 individual (matched pair) |
| Jackshaft Dimension | 1.3 |
| Jackshaft Bearing Type | Sealed ball |
| Bearing Dimensions | 1.3 bore |
| Number of Secondary Belts | 6 Banded |
| Cutterwheel Shaft | 1.8" (4.8 cm) |
| Bearing Dimensions - Secondary Belt | 1.8" (4.8 cm) double spherical roller pillow block |
| HYDRAULIC SYSTEM | |
| Tank capacity | 6.5 gal |
| Recommended Oil Type | Vermeer HyPower 68 |
| System Type | Open-loop series system |
| Filtration Method | 10 micron fill strainer and 6 micron return filter |
| Pump Flow at Maximum RPM | 6.4 gpm |
| System relief pressure | 2470 psi |
| Flow Control | SmartSweep |
| Directional Control | Electric over hydraulic |
| ELECTRICAL SYSTEM | |
| System Voltage | 12 V |
| Battery | 400 CCA |
| Warning Lights | Oil pressure, engine fault, operator presence status, clutch engage/disengage status |
| Switches | Two-speed 2x4 and 4x4 ground drive, cutter wheel engage/disengage, creep, blade (if applicable) |
| Controller | Danfoss |
| Shutdown System | Engine low oil pressure |
| CHASSIS | |
| Frame Description | Welded tube and plate steel |
| Control Station Description | Fixed side location |
| Toolbox Description | Standard |
| Steerable Axle Type | Hydraulic steering, oscillating axle |
| Degree of Oscillation | 12 deg |
| Tires - Option One | 5.7"x 8" (14.5 x 20.3 cm) dual standard |
| Fender Description | Yes |
| Axle/Suspension | Rigid/Fixed (Rear) |
| Brake Type | Spring-applied, hydraulic release at rear motors |
| GROUND DRIVE | |
| Low Speed Travel | 65 ft/min |
| High Speed Travel | 130 ft/min |
| OPTION ONE | |
| Chip Blade Dimension | Optional - 33" (83.8 cm) wide, 12" (30.5 cm) tall |
| Blade Travel Above Ground | 8 in |
| Blade Travel Below Ground | 2.5 in |
Copyright © 2026 - All Rights Reserved - EquipmentLocator.com